I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, Nordic!
We have connected gpio pins to usb data line pins for using usb or i2c in different times.
But even if USB core disconnected, usb lines hinder for i2c lines...
Hi;
I am trying to send a Telegram message using Telegram Bot API . As the documentation shows: "All queries to the Telegram Bot API must be served over HTTPS". I have...
Hello,
We are using NRF52840 and for a specific use case we will install our module on an M.2 (A/E) breakout. In this configuration USB will be the main communication interface...
Hello,
We made a small replacement on the event handler of the ble_central/ble_app_uart_c application, just to do a loopback to test the UART module.
Here is how the...
The Boron module from Particle is a nRF52840 with a uBlox LTE CAT-M module, available for $50. It's small and seems like a fun module to prototype with. I'd like to use SES...
Hello,
nRF52840-DK
SDK: 15.3.0
SoftDevice: s140
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52832.ps.v1.1%2Fclock.html
Do any drivers...
Hi Everyone,
We are using NRF52810 with latest nRF5_SDK_16.0.0 and s112_nrf52_7.0.1_softdevice. We are able to program with ble_app_UART example on our prototype,
but...
I would like to set or clear a digital pin when the button is pressed.
I seen to have achieved this with the on-board button but it doesn't work with a mesh switch.
...
I want to use the nordic 52832 hids services to get the phone of IOS mute when a call coming; I make many attempts to get it work, But I failed. So is there anyone can help...
I'm using ble_app_thingy_s132_pca20020 sdk and i fixed the code change ble_tes to ble_nus service in m_environment.c file and data send is worked.
and i also want to change...
Hi,
is there a way to change the programming clock frequency of the SEGGER j-Link programmer (I'm using j-Link Lite) in nRF Connect 3.2.0 Programmer?
I did modify the...
I was trying to set up a second computer with the NRFConnect SDK today and encountered a new issue. When I tried to install the requirements.txt for zephyr, I get this error...
I am seeing that faster advertising intervals will connect OK, and slower ones will consistently not. Specifically, a min-max of 0x1100-0x1250 works, but 0x1200-0x1400 doesn...
Hello,
We have a C# program we use in production to test and certify up to 90 of our devices at a time. We were using the nRF51 dongle and the MasterEmulator DLL, however...
Configuration: 2 x Thingy52 modules, Raspberry Pi4 (Raspbian Buster)
Development: Python 3 (3.7.3), Bluepy library
I am able to connect with the Thingy module and retrieve...
