Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
Hello,
I want to implement a proximity central. At the moment, I do not get a bonded connection from central to proximity peripheral (For peripheral i use the proximity...
Hello all,
I have realized my own board with a msp430 microcontroller and a nRF24L01+.
I have configured my nRF24L01+ as described in annex C of the datasheet; the objective...
Is it possible to use the J-link to debug a stand-alone PCA10004 ? I am not using the motherboard. Powering the board separately. When I try and run debug in Keil I get error...
I would like to ask a question about the time of :"Time between DISABLE task and DISABLED event when
the radio was in TX" of the "Jitter". In the picture show the "Jitter...
Dear nordic guy, I'm developing
with nrf51822. I have one question regarding main clock control.
I want to turn on and off 16Mhz clock in application side.
application...
Hello,
I have some code running that transfers binary data from an iPhone to a nRF51822 device (used for firmware upgrade).
I have used a variable length characteristic...
When starting with nRFgo Studio "Erase all", "Program SoftDevice" & "Program Bootloader" to have a almost virgin base without an application, I succeed perform an over the...
Hello,
currently I am thinking about the proximity concept. The following scenario is given:
We have a Display that shoud lock/unlock a Device
We have a iPhone...
I used SDK 5.1 and S110 6.0, I dowmload the project ble_app_ancs to nRF51822 DK. I try to connect it to iPhone 4s (which run on IOS 7.04), when I click 'pairing', the led...
Device: NRF51822; BMA250E
Description:
When I read BMA250E via I2C without BLE protocol, commnucation run well.
And if there is no I2C commnucation, BLE protocol can...
Hi all,
My questions are related to frequency on the soft-device firmwares for nrf51822.
In S110 does the frequency channel hop according to the CONNECT_REQ packet...
Hello,
I am testing the ble_app_hrs project on two eval boards, with s110 and s120. Everything works.
If I power-off the peripheral board (s110), it seems that the master...
Dear Nordic guy, I'm developing with nrf51822.
I have one question regarding flash write.
In ble connected state,I have some error to write some data to flash.
I want to...
