Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi All,
I've just been trying to program some of my USB dongles, nRF24LU1P-F16, via nRFGo Studio.
They are recognised fine, and seem to be operational after programming...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
Nordic,
I am using the BLE Shield v2 and the Arduino Due board to transmit accelerometer/gyro data to an Android tablet app that plots this data. I had this working fine...
First I noticed that nordic has already updated the andriod nrf toolbox app to use softdevice v7, which allows updating the softdevice, bootloader and application.
The...
Hello all,
I'm working on a library for NRF24L01+ and PIC micro.
Unfortunately there is something wrong. On the receiver side, the micro correctly detects that a packet...
Hi,
I am knew to BLE and I was able to ran succesfully the blinky project. Now when I load the soft device on and then try to download the hr example if says "Flash download...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hi,
I develop an application with the nRF51822 circuit. It is detectable with my smartphone, but not with a computer that has a Bluetooth 2.1 device. Is it possible to...
In the comment of this post , Marc Nicholas wrote:
Doesn't that require SWO to be implemented? (Which is not on the Nordic part).
Is it true, that SWO isn't available...
In SDK 6.0 I find there is a project of ble_app_hids_keyboard_serialization.uvproj in nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
and it contain...
Hey there,
today I'd tested around with the Dfu service.
Peripheral is nRF51822 running Sdk 5.2.0 bootloader example (Softdevice 6)
Central is Android 4.3 running...
I am unclear whether the soft radio takes care of updating the attribute when a write event occurs. I can see in the example codes that the notification flag is handled by...
