Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
Hi team, After executing RRAMC.ERASE.ERASEALL with an external debugger, I was unable to access the CPU (board) after reset. To resolve this issue, I connected the nRF-programmer...
Dear Customer Support,
Wanted to open a case to follow up on this old one Case ID: 335484
I initially looked at the counter alarm under
https://github.com/zephyrproject...
Hello, I would like to ask if the latest SDK version supports power management on the FLPR core of the nRF54L15. According to this article, the power consumption is quite...
hello everyone I have implemented BLE, ADC, RTC, and UART. After that, my power consumption is around 1.31 mA. Can you suggest possible ways to reduce power consumption or...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up to read the potentiometer's raw value . As part...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
Hello Nordic Team,
I am reaching out to ask for some advice and/or guidance on how I may debug code that:
1. Is initialized and runs BEFORE main
2. Is part of the zephyr...
Hello,
we are developing a device which implements BLE hid keyboard. The code is based on the hid keyboard example in the NRF Connect SDK.
The example uses battery service...
Hello,
I am planning on using the WLCSP version of the nRF52840 chip on a PCB design. ( nRF52840 - Bluetooth 5.3 SoC - nordicsemi.com )
Is it possible to program the nRF52840...
I'm attempting to write software onto a newly purchased nRF52840 dongle using nRF Connect for desktop, but I'm unable to do so. My environment is Ubuntu 24.042 LTS. The LED...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hi, I'm a novice in embedded systems. I have board based on nrf52811 and firmware written for my device but when I received my board from production I could not load firmware...
Hi all,
I'm modifying the Matter Light Bulb example from Nordic's nRF Connect SDK to integrate I2S audio output on the nRF5340 DK. The goal is to play a continuous beep...
Hi,
I am working on zigbee demo "light_switch" with NCS2.8 Add-on SDK.I enabled MCUboot according to the steps in the course " Lesson 9 – Bootloaders and DFU/FOTA "
1...
Hi,I am using NRF54L15 DK in which I need to transmit audio data over BLE where that data will be used for only plotting in application,I am using sampling rate of 16000 and...
