Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I have a problem with a specific Zigbee certified device that I can't connect to my Nordic device.
When trying to connect to the device, I go to see the status:
...
Hi,
In need to debug my application using segger IDE when there is bootloader already present in nrf52832 chip .
The sdk we are using is SDK 15.3
Bootloader:- "secure_bootloader_ble_s132_pca10040...
Quick project overview:
Mesh network using nRF52840.
Nodes need to be able to be controlled individually (setting GPIOs) and also report back data (ADC, GPIO state) to...
Dear sir/ madam,
I have two questions regarding NRF52832 as follows:
1. Will nrf52 only get connected to apps provided by nordic? I want to it to get connected to serial...
Hi,
Greetings!
I am using following setup
1. Mesh SDK: 4.0.0
2. SDK 16.0.0.
3. Segger Embedded Studio on Windows 7
I had a look at "pwr_mgmt_pca10040 " example...
I slightly modified the qspi example code to try something that I'd eventually like to implement as part of my application. But when I try to interleave reads and writes then...
Hi,
We did stumble upon an issue with our BLE peripheral running on an nRF52832 with Softdevice S132 5.0.0 . The central side is implemented on top of the UWP (Universal...
Hi. I want to run the pca10059 dongle so that the BLE is in central mode and is recognized as a virtual port on the pc. Is it possible to operate with only UUID settings in...
Hi, I recently bought some nRF52 DK rev 2.0.0 (2019.25) boards from a US-based distributor. The distributor seems to not be in the loop on the specifics of the design, as...
How do I use the device root key to encrypt and decrypt?
I can set the device root key in the cryptocell register, but not sure how to use it. I am using Zephyr by the way...
Hi, nordic engineer:
Our project has a function, that is, BLE+Thread coexists. We hope that the mobile phone can upgrade the device through BLE. Can this idea be realized...
Hi All
Now I am testing the example code \examples\ble_peripheral\ble_app_uart with Nordic nRF Connect app on smart phone. i do a limit change in function uart_event_handle...
Hi,Master:
Platform: nrf52840
Bluetooth protocol stack: s140
When using qspi to communicate with external flash (communication speed 32M), occasional qspi communication...
Hi,
I have been working with different boards to implement different ML TensorFlow Lite samples in the 52840. I used Particle and Arduino BLE Sense.
All forks from the...
