Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Hi, I have issues configuring PSM together with RAI on my nRF9151-DK. I am trying to send UDP packet, wait for response and go to sleep for several minutes trying to consume...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
Hello
I get the following error code, when I try to build the button sample with my custom board. I try to build and flash via RTT Hello World with my custom board and it...
Hello,
I am using the nPM PowerUp application with the npm1300 Evaluation kit. I am trying to configure the bucks (1 and 2) to be on/off controlled by one of the buttons...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Why project config is not finding relative path of these files but absolute path works fine:
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip-DAC-Cert.der" ...
Hi Support Team
Could you guide us build an efficient automatic programming tool for nRF54L15’s mass production? Our Apple Find My and Google Find My project will be mass...
Hi
We have a Nordic thingy device with us & using that we would like to perform some network testing.
We are setting up a private NB IoT network and we would like to...
Hi,
1.Please provide the documentation, examples and tools for testing the RF performance of nRF7000 during the mass production of nRF9151 + nRF7000. 2. If not, please provide...
Dear colleagues, I am using the Nordic nrF9151-DK as part of exercise1, lesson 2 of the intermediate Devacademy course. Lesson 2 is about trying and using the various vscode...
Nordic #Devacademy intermediate course: Ticket for exercise 1 of lesson 3
Dear Colleagues,
I passed the test for lesson two, with only getting exercise 1 to work. Now...
Hi,
I am currently working on a two way communication between an nrf52840 thread host and an nrf52840 thread client over coap. I have nrf connect sdk version 2.9.0 in both...
Hi, not exactly a problem rather it is question on whether this setup is suited for what I want,
I want 3.3V for the device and sensor systems, possibility of reducing...
