Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
I'm running the Nordic/Thread SDK 3.2 with an NRF52840 (Rigado BMD-340) on SES 4.42.
I've got a project using BLE + Thread and I'm having problems implementing a hardware...
A multiperipheral connection to a central, all with custom nordic devices (nRF52840) has been stablished. Comunication and connection work just fine, but after a synchronization...
Hi ! I am represnting company responsible for fruitymesh ( https://github.com/mwaylabs/fruitymesh ) which is an open-source proprietary ble mesh running on nrf5 chips. For...
Dear Support,
I have adjusted the radio test example in SDK16.0 for my custom hardware application using the nRF52840. I have followed the instructions on this page to...
To the kind attention of Nordic support team,
As it was said https://devzone.nordicsemi.com/f/nordic-q-a/57531/sdk16-nrf52810-secured-gazell-keil
the secured gzll library...
Hello,
I'm able to program the code (below) to the nRF52 DK. Leds 17 & 18 are working.
I'm unable to program the code to my custom board. Leds 9 & 10 are not working ...
Is there any problem with beacon advertisment and ADC? I have 3 adc pins configured to measure three different sensors... When i use UART over BLE... everything is ok.. but...
Hi!
I seen video and read manual how to use it, but still not doesn't work.
PPK + PCA10040
on the PPK board I set jumprs to DK (all 3 pcs). USB connected to PCA10040...
Looking through the datasheet, current consumption is provided for the nRF9160 Modem at 3.0V and 3.5V. Is it possible to get information on 5V related current draws? I've...
Hi,
I am using the example nrf5-ble-mpu-simple from nrf5-mpu-examples-master to do the following:
a) send a BLE beacon advertisement (non connectable)
b) periodically...
We are currently having an issue with DFU failing on Samsung A7 a running andorid 6.0.1. We are using nRF Toolbox for BLE (DFU application) and when I try to connect the device...
Good day!
I'm working on Time model fro Bluetooth specification.
Question is about time handler. I can't figure out should I write a separate handler for TAI, or I should...
Hi!
I´m currently using the nRF52840 demo board to determine the bluetooth range of the device I'm working on.
The question is: which is the orientation of the antenna...
