Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi,
I have a mesh network with multiple smartphones, which are connected over GATT. If now a light command is triggered on one smartphone, I want to synchronize the other...
Hi Sir,
As we know the SDK has the lowest version of IDE to compile.
========= release note of SDK 16.0 ============
The following toolchains/devices have been used...
Hi,
Every now and then we have to fix bugs in nRF Connect SDK. Some of the bug fixes are of general interest. What is the process for contributing fixes to Github?
BR...
Debugging in Segger serial example from mesh
It runs and responds to commands, but when paused or hits breakpoint - single step or continue gets to address 0xa60, continue...
While setting u p a sample project in SEGGER Embedded Studio, following error is encountered
All the previous installation steps were successful and verified.
Please...
Hi,
I am trying to implement SPI slave on NRF52810. I added nrfx_spis.c and enabled below macros in sdk_config.h
NRFX_SPIS_ENABLED and NRFX_SPIS0_ENABLED to 1
Still...
Hi all,
I am using SDK 15.3 with NRF52811 chip.
My application include app + bootloader.
In my application, I use flash area from 2E000 to 2F000 for save my user data...
hello
i want to create for the need of my project a thread border router as simple and compact as possible.
i have seen the implementation using a raspberry pi 3B as the...
Hi,
I followed this guide to send data to the GCP using the Thingy:91 : https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-connect-nrf91-to-google-cloud...
Hello,
i'm trying to set the automated test script as described here:
https://github.com/NordicSemiconductor/Android-nRF-Connect/blob/master/documentation/Automated%20tests...
Hi all,
I am a newbie in ble and also nordic. I have an application need that would do some lowfi sound data transfer which 16 bits at 14k sample rate from central device...
Hi,
Good Day!
Statement of problem: Currently we are using app_timer in our application for conducting the user behavior. For example, for user input off of capacitive...
Hello, everyone. I am newbie in use the Power Profiler Kit I followed all the steps as described in PPK User Guide v2.2:
1 - cut traces on the DK (SB40) 2 - installed the...
Hi,
I am porting a BLE program in nRF52832 EVB, and it can work correct.
The system will not work when I want to remove 32KHz crystal from my own real board.
Would you...
Hi,
So we are currently debugging our custom nrf52832 board. It is equipped with both a 32.768khz and 32Mhz Oscillator, which both SEEM to work.
I tested both using the...
