Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
I am using nrf51822 custom board.
I'm trying to make intterrupt when a pin is 0 (or 1) and do some calculations while it remains 0.
However I could not manage...
Hello,
I am trying to use SPI on a mbed nRF51822 and am following the documentation suggestion. We've deleted all code except the minimum to try and track down the problem...
Hi,
i want to build an applicaiton with gcc and eclipse setup and S130. I use OSX.
if i don't use the softdevice and run it with the blank linkerscript my blinky code...
Hello,
We are trying to update to Keil uvision 5.11 and unfortunately breaking our teeth on the pack Installer. The Nordic SDK 5.2.0 is installed on the machine but when...
Hi,
I have installed nRF Master Control Panel app on custom board running Android kitkat 4.4.2(ASOP).
But when I run MCP app it gives prompt that 'Device doesn't support...
Hi all,
I develop a central application, which manages multiple peripheral connections. The application often has to stop and start scanning again. In rare cases the function...
Hi,
I'm trying to get the bootloader from SDK v6 running with SoftDevice v7.
I managed to compile it under Eclipse (gcc). I've just removed buttons and LEDs from the code...
I would like someone from Nordic to confirm that the new softdevice release s110_nrf51822_7.0.0 is not suitable for the 128kb versions of the chip (in my case nRF51822 QFABB0...
Hi!
How is the functionality choosen, the nRF51822 has to offer?
Is the SoftDevice (e.g. SD120) an API in C where a specific functionality (e.g. central role listening to...
Is it possible to use nRF51822 Development Kit without nRFgo Starter Kit? What I need - is to be able to connect couple of LEDs and buttons, can this be achieved without buying...
Hello,
after successfully calling sd_softdevice_enable(), I call ble_cscs_init() and that function returns with error code 7, which means NRF_ERROR_INVALID_PARAM. I've tracked...
Hi,
After doing an sd_nvic_SystemReset(), the bootloader does start advertising, but for some reason the android app nRF Master Control cannot connect to it.
If I connect...
Hi everybody,
I'm currently writing an Android application allowing me to communicate with a NRF51422.
I've created on the Nordic chip one proprietary service with 2...