I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
I've been trying to install the newest nRF Connect SDK using the Toolchain Manager with the appimage The toolchain and SDK installations seem to be successful however when...
Hi. We have a custom board with an nrf1960, which we use to communicate with Azure IoT Hub over LTE-M. We are updating from NCS 2.4.2 and modem firmware 1.3.4 to NCS 2.7.0...
Hello,
We are currently in the process of developing a custom board containing the nrf5340, which will act as a central for HR devices and a peripheral for data transfers...
Hi
Can someone help out?
Why is there an empty PDU after every notification(length shown in trace with 277, my payload is 244). Are all packets with the same EVENT COUNT...
Hello!
Since we are moving from the prototype phase of our project to the pre-production phase, we have developed a custom board which utilizes the ISP2454, nRF54L15 SoC...
Hi,
I want to develop a new project without using NCS way. For this project, I didn't use the Kconfig and deviceTree.
The hardware I use is NRF54L15-DK.
My purpose is...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi
I connected RF Connect for Desktop to "nRF54L15_DK" in my Desktop
when I want to use Direct Test Mode,press Start test bottom,the log show "DTM setup reset command...
Performance on hardware (cc3xx) is significantly slower than performance on software (oberon). Does anyone have a good explanation for this? I have also tested ECDSA and can...
Hello Sir,
I am currently working with the boards:52840dk and ncs:2.9.1
Regarding the issue of failed mcuboot upgrade after writing the upgrade firmware using flash APIs...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
I have this main code:
With this overlay:
and this configuration:
I am using a nrf52840 dev board and have connected P0.06 and P0.08.
Why does it not trigger...
I'm playing a bit with MCU boot and folowed the tuturial . When I compile the sample with mcuboot from Zephyr, it works fine for the 52840DK, but when I try to compile for...
