Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Trying to make Thingy91's asset_tracker_v2 light sensor (BH1749) data to show up in a card on Dashboard in nrfcloud. By default asset_tracker_v2 code supporting light sensor...
Hi, We have used nPM1300 on our development board around nRF54H20, but we are experiencing an strange issue. - when power is attached VBUSINILIM0/VBUSINILIMSTARTUP value is...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
Hi,
I'm currently using the nrf52840 SDK board and based on ncs 2.9.0 SDK. I need to make a simple sample customer bootloader that does not use the DFU and MCUBOOT functions...
Hello Nordic,
I am looking for a sample or instruction (step by step) for custom bootloader.
Our application code is ready and all the left thing is BLE DFU and custom...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
Hello,
The subject of this post is mostly accurate in that I am developing custom hardware that is based on the nRF7002DK. For all intents and purposes, the Interface MCU...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
Hi,
I'm trying to send HTTPS commands (GET/POST) using the nRF9151-DK.
I’ve already completed the process using nRF Connect for Desktop . The device was recognized correctly...
