Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
Hi,
I am using ble_app_hrs application as a reference code.
in our case i have gpio interrupt for every 25 ms.
what should i keep BUTTON_DETECTION_DELAY for 25ms...
Does the lcd clobber the tmr0 and/or ANT ???
We just went through several days of working w/ ns on running ANT w/ RTC with a resolution of using sd_ calls.
Is the LCD...
Hi,
i am using nrf51822 custom board.
For our application i am using ble_app_hrs source code.
in that i have gpio interrupt for every 500ms, to get data from accelerometer...
For example, if I have a GPIO pin configured with low sense, and it goes low just before I call sd_power_system_off(), will the device return to System ON mode immediately...
Hello,
I've got a nRF51822 DK which I try to program with a SoftDevice using the nRFgo Studio (nRF51 Programming). My chip/programmer seem to recognized properly since...
Hi,
For developing our application i am using ble_app_hrs
in my case i have gpio interrupt for every 500 ms to get data from accelerometer.
question:
in heart...
Hi,
I am attempting to understand the timing of events when a mobile application connects to my nRF51822 based device. The reason being is that I have to enable the UART...
Hello,
Greetings, in the nRF24L01 datasheet, its mentioned that the module can work as a multiceiver, meaning 5 nRF24L01 module acting as PTx can communicate with 1 nRF24L01...
hi,
my customer using nrf51822 DK to have debugging software,the error occur in the attachment.
can you tell me something have Caused this problem?
thank you !...
I am using the code
err_code = sd_ble_gap_device_name_set(&sec_mode, (const uint8_t *)deviceName, nameLen);
I have made sure that nameLen is less than BLE_GAP_DEVNAME_MAX_LEN...
Hi
i am using twi_hw_master.c for i2c communication of accelerometer.
my accelerometer address is 0x18.
once i call
twi_master_transfer(0x18,dataW,1,1);
in...
Hi,
Can the value of NRF_RTC1->COUNTER be read safely from the main loop without first stopping the RTC or temporarily disabling the RTC1 interrupt etc? (nRF51822 or nRF51922...
I used the nRF51822 Evaluation kit and flashed the BLE_proximity example on to the PCA100001 board.
In the master control panel the USB dongle measured -46 dBm(Nordic_prox...
Hi all,
what if I want a sensor network in my house with BLE. Can I just install, for example, 16 nodes in my house and connect to all of them with one iPhone? Or would...
