I’m using the Zephyr nordic,npm1300-charger driver on an nRF52840 to control the nPM1300 PMIC charger. At runtime I need to be able to turn charging on and off—on command...
I have a greenfield project that I am currently working on and I am trying to work out the best approach to limiting access/features via Bluetooth.
In the past we have used...
Hello dear Nordic support staff,
I'm working on some legacy code (NCS 1.8.0 in case it's relevant) and see this in the inclusion list of one of the files:
Functions...
Hey there!
I'm trying to run the 'wifi/shell' sample on v3.0.1 on a nrf7002dk (targeting the nrf7002dk/nrf5340/cpuapp) with sysbuild enabled, of course and I'm getting...
Hi Teams
I am designing a product using the 9151 SIP. According to the specifications, the operating voltage ranges from 3 to 5V. From the hardware design guide, I learned...
We have a design in EVT and we're preparing for FCC testing. It's a dual radio board with nRF52840 and a Semtech LR1110. Therefore, we need both to be active and transmitting...
Hello Everyone,
I want to run a couple of test on the nRF51422 radio. However, how do I go about checking the firmware on these devices without the use of a motherboard...
Our device fetches fused quaternion from MPU and transmits via NRF 51822.we are using 3.7v li-ion battery.we are using Non-volatile memory.
Currently we are facing these...
I am trying to run BLE central peripheral dual role on nrf52 pca10040 with nrf_uart as service. Also, I have redbearlab BLE nano as peripheral (nrf51822 based).
I am getting...
Hi, I would like to ask that, whenever I put my function in main.c, the borad become undiscoverable.
I'm using nRF51 with ble_app_uart_s110_pca10028, and below are my function...
use nRF Toolbox APP to bonded peripheral device even disconnect and connect don't need input PIN code again, but when I turn off BT the APP lost bond information. next time...
Can the S120 work without RTC XTAL?
Iam using SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION, false);
but it still hangs in the softdevice_handler_init...
Hello,
I am attempting to implement the TWI drivers from the SDK for a nrf52832 chip for a pca10040 board. I am using the twi_hw_master files to drive my TWI and insofar...
Hello.
Since i migrated from 1 to 2 SPI bus, IRQ Handler at completion is not called. Can I use 2 easy DMA SPI ?
1 bus was working fine.
here is my config
/* SPI...
Hello Nordevzone:
8.0 multilink example
I tried to use this modified handler to receive notification data from a s110 based application. The centerpiece of the handler...
Hello! I have been playing with this example and got some LEDs blink here and there, but would very much like to have UART working as well. The documentation states that ...
Hi,
I'm using the nRF51822 for a beacon and following the ble_app_beacon example (SDK 8.0.0) with some modification in order to measure the battery level through the ADC...
Dear Nordic:
I try to use pca10040 DK and SDK is nRF52_SDK_0.9.2_dbc28c9.
Test nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\UART the function work well on my DK.
I...
Hi,
I have some questions regarding connecting multiple (as many as possible) BLE peripheral devices to a single central (simultaneously).
1:
Does anyone know of any...
Hi
I now is developing Android apps on the basis of NRF UART v2.0.
My s110 NRF51 device will switch two modes for differnet 128-bit UUID. These two modes have independent...
