Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I've playing around with the new peer manager a while. I used the example "ble_app_hrs_rscs_relay_pca10028.uvprojx" from the SDK10. After a first fix (see Link ) in...
Hi,
I want to use timer1 or 2 interrupt ISR to generate complicated PWM signal.
but the timer->intenset setting cause ble connection drop problem.
Please refer to my...
Hello. I'm having the following connection module with nRF51822 chip.
It was purchased here .
I've found example sketch for Arduino but i can't understand how to wire...
Hi,
I have been developing using some development modules from WaveShare (based on the nRF51822 QFAC) and they work fine.
However, I'm now trying to use a module better...
Hi Nordic Expert,
I am Alex and have been developing with NRF51822 for a long time. Thanks for your quick help before. Now our product bases on S110-7.1.0 and SDK-6.1.0...
Hi
i wrote the program which is making pulse one time on channel 0 and then followed by channel 1 and then again channel 0 and then 1 going on , my aim is to create pulses...
Hi all,
I am tring to connect more than two peripherals to contral device.
I am using sdk10 and three evaluation bords nrf51822.In on device i debbuged the code of uart...
My problems with Eclipse Luna continue. Going on holiday for a week I assumed the good fairies would sort it out, but no,,,
Anyhow, I'm sure it's some path error somewhere...
I'm trying to figure out something I'm seeing. I've modified the relay demo in the nRF52 SDK so that when I press button 2 on the board, it destroys any connections, erases...
Hello Everyone,
I have configured gpio pins for buzzer pin6 and pin 7 and am trying to clear those pins after buzzer making the beep sound but it is not getting cleared...
hello there i downloaded nRF51_SDK_10.0.0_dc26b5e.and run this example experimental_ble_app_blinky_s110_pca10028. here when i write 1 from master control panel LED turn on...
Hi,
I've asked a couple of questions around this before but that was before I thoroughly researched into what I was actually asking.
I would like to attempt to use the...
Hi,
I am currently working with the nrf8001-DK. I've connected the nRF8001/nRF24L01+ shield adapter to an Arduino UNO R3.
I've run the ble_uart_project_with_dfu_template...
