It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi all,
i am new to nordic and I working on the project to scan/locate iBeacon by using nRF51822,
I can't found a related sample code on SDK 5.2.
Is there something I...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I have built a board using a reference design for the USB dongle board for the NRF24LU1+. Now when I connect to the USB the system identifies the device as "nRF24LU1+ -F32...
Hi!
I just ordered nRF51822 and nRF8001 chipset from Digikey, not dev KIT. I want to develop product by ourself based on nRF51822 and nRF8001 chipset so I want to have all...
In s210 there are functions sd_flash_page_erase, sd_flash_protect, and sd_flash_write. There is no sd_flash_read.
How do I read from flash? I can write to is using sd_flash_write...
Hi
I just want to create a custom service with a characteristic, which sends "n" (upto 200) bytes at same time and this bytes are are written to a SD card via SPI
So...
Hi, I have been using the nRF8001 Arduino SDK with nRF8001 chip. I wanted to set the data for the different services I'm using and thought I would go ahead and use the services...
Dear sir
Now, I am trying multi-link examples at SDK5.2.0 S120 example. I found s120 central only can receive one byte data from s110 multi-link peripheral. Could we modify...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hello,
I have some problem with NRF24L01+. I'm trying to make bidirectional connection between two devices with this chip. When I'm sending payload with ACK, TX_DS interrupt...
