I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
NCS 2.9.1 - NRF5340DK
I am trying to use multiple compare channels on Timer1 (output_timer) such that an interrupt handler fires for both compare values, the second of which...
I used a mesh example (the example name is "mesh") for testing, and enabled low-power nodes using CONFIG_BT_MESH_LOW_POWER =y, and disabled the automatic start of low-power...
I used ncs2.9.1. I download the mesh dfu distributor and mesh dfu target examples to two devices respectively, and successfully updated the mesh node through shell commands...
Hi
We are using the CMakePresets.json file for different variations of our firmware. Since the latest update (2025.4.106) the build configuration interface changed a bit...
use "nrf5340 cpuapp" to compile project, flash statistics as follows, see blue color
[3/11] Linking C executable zephyr\zephyr_pre0.elf
[6/11] Linking C executable zephyr...
Hi, I am a beginer, it is my first time using raw MCU IC, and I don't know how should I connect my 32MHz oscillator. So I see that the nordic configuration looks like this...
Hi,
I’ve compiled and flashed the Matter light bulb example from Nordic onto the nRF5340 DK.
I'm using the nRF52840 Dongle as the OpenThread Border Router, with a Raspberry...
Hello,
I have a custom hardware around the nrf52820, and I simply can't make it to run the basic hello_world and blinky samples.
I'm compiling the samples using nrf52833dk_nrf52820...
Hi,
I've just migrated my project from NCS 2.6.1 to 2.9.0 and I'm having some problems with the UART.
I'm using the nRF52833 DK to communicate with another device and...
Hello,
I want to port blinky example to 52805.
I wrote this dts file:
I added " CONFIG_DEBUG =y" to prj.cong.
I launch debug but main function is never reached...
I discovered weird modem behavior when testing my application with a weak or undetectable signal. Mine testing was as follows:
modem connected to the network
communication...
Can the npm1300 be set up so multiple interrupts trigger the same line, and then the host can determine what the cause is?
Or does each interrupt need a 1:1 correspondence...
We are developing a device that uses BLE, 4 contacts (buttons), a piezo connected via PWM and a realtime clock (RV3028). It also stores event data on an external flash using...
My application communicates via UDP and all communication is initiated from the device. Before packet transmission, network registration status is checked (CEREG) and sendto...
I boot AOK after I do a west flash --erase. But after that, when I try "west debug," I run into this:
*** Booting nRF Connect SDK v2.9.0-2e7ce73f5faf *** *** Using Zephyr...
