the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
DECT NR+ HARQ communication and testing
Hello,
we using two nrf9151 development boards with latest modem firmware version DECT-NR+ (1.0.2) and nrf-connect v2.9.0 and...
In our custom board, (nrf5340-nrf7002), We are observing a Wi-Fi connection time of around 4–5 seconds, even when reconnecting to the same router. As our product is battery...
hi,i am using zephyr`s sample of gpiote,it works well,but i don`t know how to optimize the power consume of gpiote:
1,how to setup PORT EVENT?
2,Sometimes i want to reduce...
Hello,
In my project I use a nrf52840 which have the access port protection. I am in the development phase and I would like to disable this protection during this phase...
I'm developing with an nRF52832, NCS v2.6.1 and Zephyr 3.5.99
I've been forcing my MCU into System Off when I don't need it to do anything, then triggering it out of that...
Hi DevZone Engineers,
As I am unable to access my board (Xiao BLE Sense (embedded form) with Nordic 52840 SoC) through the "Connected Devices" tab in nRF Connect, I am trying...
Hello!
I'm new to Nordic Semiconductor and currently developing a project for which I need support regarding the nRF9151 DK . Before placing an order, I would like some...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hello Everyone,
I try to develop Nuvoton + NRF24L01 SPI communicate each other. And I don't understand why MISO bus has 0x0E after I send Write_Command 0x20?
void NRF24_AdressTX...
Using FreeRTOS and SDK 15.3 on nRF52840 and SES, SD 140
I'm following along with the NUS example project in this particular release and have a problem I'm a little stumped...
Hi,
I’m facing an issue with RTT logging on my nRF52840 using NCS 2.6.0. I’m trying to log output from the B0 bootloader, but so far, I’m only able to capture logs from...
Hi, I am trying to set my acqtime different to the max value. And the build throws an error unless i set it to ACQTIME_MAX.
It appears in the header file it needs some other...
We are trying to add CarbonDioxideConcentration cluster in matter. we are able to add temperature and humidity clusters and values which are updated are getting read in chip...
