Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Dear Dev Team,
I am currently working on implementing OTA DFU on the nRF52832-DK using the Arduino framework. However, I have not been able to find any suitable options...
Hello!
I am currently using INA219 (Zephyr I2C driver included) current monitor to test I2C function on nrf54l15dk, but the board cannot recognise the sensor successfully...
I am trying to build using a custom board and 2.9.1, but am getting these errors:
My dts looks like this:
I have the width specified. Much of this is over...
I am currently looking into the Legacy DFU process. Currently the only way to actually conduct a Legacy DFU is via the nRF Connect Mobile App. After conducting a successful...
Currently using NCS v2.9.1 nrf54l15/cpuapp custom board derived from nrf54l15dk, customization to de added after solving the issue below.
The project is successfully compiled...
Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
Hi,
I'm using the Ellisys tool to capture packets and compare the differences between CIS and BIS. The capture results for BIS show that it is unencrypted, as seen in Figure...
Hello.
We're trying to expose and use the Wifi stack in micropython in our project for the nRF7002. We've managed to get Wifi scanning to work (based on the sample code...
We have developed a hardware platform using the NRF5340 on Nordic's zephyr (version 3.5).
Our current consumption in idle mode is still around 330 µA, instead of the expected...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
Hi, I'm working on the DK for nrf52832. I have a working code for BLE, and another working code for die temperature using interrupt. Now I want to merge them and trigger the...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
We have an nRF52840 device that is required to do continuous BLE scanning in central role to find nearby advertising beacons and is never required to establish a connection...
