Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
I just want to double check something before I optimise an implementation.
If burst is enabled on multiple channels, let's say x256 for two channels, internally is the process...
I use nrf5340 DK as AP, nrf54l15 DK as TAG.
Below was uart print comments from AP
ESL_AP:~$ > esl_c bond_dump
esl_c bond_dump
Dump bonded device
ESL_AP:~$ > esl_c...
I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
Hi, I'm working on a project and I need the GPIOs to have 3.3V available when the nRF52840 is in deep sleep, in order to use wake-up on GPIO. So I'd like to know what the...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hi,
normally, I would set the CMAKE_BUILD_TYPE to `Debug` to enable Cs "assert" function (not define NDEBUG). Zephyr (and Nordic-Zephyr as well) has the `CONFIG_ASSERT`...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I am currently developing a project using the nRF51822 with SoftDevice S110 v8.0.3 in Keil uVision.
To properly manage RTE components and dependencies, I need to use the...
Hi,
As the title states, after a while, the nRF7002 fails to connect SSID after a while. It happens either we perform net_if_up/down or not. I suspect the nRF7002 to be...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
