why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Hi, I'm working on provisioning a Pre-Shared Key (PSK) during manufacturing for an nRF5340 device. The device needs access to the PSK at runtime to generate authentication...
Hi,
I tried to add a pairing PIN code feature for connection with a central device (based on the reference: Migrating to Peer Manager ) in the ble_app_uart example of the...
nRF54L15 would be used as thread RCP, host processor would use uart to communicate with the rcp. They would behave like a OTBR.
I also need to do device firmware update...
I have created a custom board with an NRF52840 on an Ebyte E73-2G4M08S1CX. I am trying to burn a bootloader to the chip using OpenOCD and a Raspberry PI Pico W as a debugger...
Hello, I'm developing with an nRF54L15 Revision 1 (QFAA-B00). I'm encountering a problem described in the errata: 3.4 [8] SPIM: Wrong data is transmitted on MOSI (Symptom...
Hi,
I am using the nRF52840 with nRF-SDK version 16.0.
At random intervals, I encounter the following error:
"[00:02:51.009,460] <error> app: ERROR 1813 [Unknown error...
the older nrf52-DK has a header for external and one for current measurement.... how do i achieve something similar on the nrf54L15-DK, which exposes the 3-pin P6 header?...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
After programming the DK, it "fails to verify device" with the following log:
2025-07-08T09:42:05.940Z INFO Initialising the bundled nrfutil device 2025-07-08T09:42:05.957Z...
Hello guys!
I have a strange problem where the nrf9151dk suddenly won't power up. It was working fine - I was only working with SW, not HW.
I got a pop-up error saying...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
I have a service and characteristic that is Notifying data at a rate of ~160 kbps.
Both our custom app and the nRF Connect app appear to be receiving the same packet over...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
