Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I'm using nRF5_SDK_12.0.0_12f24da and s132_nrf52_3.0.0_softdevice to do the mutilink and it's almost ready. We want to do the OTA on it. I think the mutilink is working...
Hi there,
It isn't obvious from the reference layouts on the downloads page for nRF51822-CFAC if the ground plane is supposed to create a 50 Ohm trace going into the balun...
Hello everyone, i have a task where i need to transfer 50-100kB of data from ble peripheral to a central device. I have read many posts here and i have a pretty good idea...
Hi, I work with the nrf51-ble-driver_win_0.5.0. I changed the heart-rate-collector to discover the characteristic of connected devices. Maybe I'm blind. But the ble_evt_handler...
I want to accomplish something very simple: use a timer to output a continuous square wave on a certain pin, at 30-60kHz or more. It doesn't have to be PWM or anything fancy...
Hi,
I'm working on a BLE application which use ECC.c (Elliptic Curve Crytography). The problem is Keil has found an Error:
._build\nrf52832_xxaa.axf: Error: L6218E:...
Hello Support Team,
I am developing a BLE project use of nRF52832.
My work base on SDK 12.1.0, I have research these workflow, I find that are 3 channel radio when RSSI...
HI
I'm trying to connect a heart rate sensor to nrf51822 but I cannot find a suitable sensor. Could you please recommend a heart rate sensor which nrf51822 can support...
I am using nrf52832 with softdevice s132, it use the power manage function to enter to the sleep mode.... But i cannt recognize whether it is in sleep mode or not.. Can anyone...
Hi,
I am trying to port pca20006 smart beacon kit code to pca10028.
I have attached main.c --> main.c
I am currently using following ROM and RAM configuration for pca10028...
I want to know that how to judge the Traffic block.
If there are 1 BLE and 1 android APP. It must be ok.
if the number is 2,3,4,5....n
What is the maxium n?
How to cal...
Hello,
I am using a custom board and my setup looks like this:
nrf51 chip
16KB RAM
256KB of Flash
external crystal of 32MHz
SDK12.1
Compiling on Linux...
Hello,
I am trying to read values from MPU9250, I can read them from accelerometer and gyroscope but when I try to read from magnetometer i cant get any values on UART...
