Hi,
I am currently making an upgrade og a nRF51422 project that has both BLE. and ANT+ Cycling Power profiles and if I run the old project on an 51822 processor I can see...
Further into development of the ReRAM file system. I noticed that in generated DTS for nRF54L15 board for the ReRAM we have:
What is the reason for providing erase-block...
Hi,
I am developing for the 54l15 using nrf connect version 2025.5.92 Last Updated 2025-05-15, 10:08:43 and it's starting to seriously frustrate me.
The nRF Connecot for...
Hi, I have two firmware images: A and B which I need to make compatible for OTA (DFU over BLE using MCUBoot - the standard process described in the devacademy course ). They...
Hello community,
I'm currently working on setting up SPI communication between two nRF5340 DK boards , but I'm running into several issues.
SDK Version 2.9.1 : I couldn...
Hello, I just try to migrate our developing project from old parent-child build to sysbuild,
But when I build the project with non-secure cpu (with TFM), I get the <err...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
I am working with the DWM3001CDK board for Ultrawide band, but would like to use one of the free LEDs on (P0.14, P0.22, P0.05, or P0.04) as a way to show that the 3 AAs powering...
Hi,
We’ve designed a project using the nRF5340 + nRF7002 combination, with Wi-Fi connectivity enabled.
As part of our preparations for FCC certification, we’re currently...
We designed a nRF54L15 custom board and now want to add nRF21540 FEM module to our device tree as follows:
/ {
nrf_radio_fem: name_of_fem_node {
compatible = "nordic...
I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Dear DevZone,
While porting our project from NCS 2.9.1 to NCS 3.0.0, I ran into linker errors when building LVGL. The linker reports that it cannot find functions defined...
How do I map the build codes noted in the Rev Errata to the stamps on our ICs? I have two versions with QFAAAB and QFAABB stamped on them but the documentation says QFAA-B00...
I'm developing my product using NCS. It compiled fine yesterday, but today when I opened VS Code with the nRF Connect extension, it prompted me to install the toolchain. I...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, I want to disable parts of my RAM to save power. I implemented this in my project based on the System_Off ram retention example. I'm now not sure if RAM retention is...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
My application is based on the ncs nrf5340_audio application, but my application and hardware target are both out-of-tree and I am using ncs v2.9.0.
I am able to connect...
Hello,
I have a firmware that sends every 15 min a packet to nRFCloud using nrf_cloud_coap_json_message_send().
The code is working great most of the time : hundreds of...
