My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi all,
the release note of SDK 4.3.0 reports that it was tested and verified using BLE S110 version 5.2
When it will be available (version 5.2) ?
Actually we can download...
Hi,
I want to read the data by the radio.now I have read the temperate data from the tags by 51822. the data include the ID value and the temperate value. the ID is hex ...
Hello,
I'm working with nrf51822 on a custom board and i'd like to use the LPCOMP as wakeup source. I configured the module by the code listed above:
void lpcomp_init...
So now that I understand the problem with overlapping asserted events on the GPIO port, I can't figure out the correct way to reset the sense field in the GPIOTE_IRQHandler...
Hi,
I follow steps in User Guide version 1.2. The Blinky project is working fine.
Then I program SoftDevice and after than compile and Download HRM using Kail
But led...
now,i pairing my peripheral and Communication read/write data. but have some issue for disconnect/reconnect .
1.disconnect: when i disconnect (call didDisconnectPeripheral...
Hi,
We are using Nrf51822 , pca1001 evaluation board.
when i flash bel_app_proximity code (by disabling led function in advertisement_star()),
current consumed by...
Hello Developers,
Just started with the nrf51822 and managed to install:Keil 5.05, Segger J-link, nRFgo Studio 1.16 and the Master Control panel. I also loaded the SoftDevice...
Hi,
I'm knowing the device_firmware_updates project in SDK and I want to know whether I need to program the softdevice when I do the device firmware updates over UART?...
I am developing a windows application, using the MasterEmulator api.
I am discovering BLE devices with scan parameter Active and Passive.
The result is that most of the...
HI,
when I used nRF51822 for 2.4G transfer ,I found that RX can't receive data in some direction .Can TX use two antennas and matching networks to work alternately in order...
Hi all,
I am currently working on a BLE project based on the PCA10001 evaluation board. I am trying to follow the nRF51 application note. I have done everything that the...
Hi
I'm using the nRF51822 and custom a service.I add 4 characteristic in the service and all of them
config to indication type to send data.Everything is Ok and sending...
Hi
I'm just starting with all this. My set up is a nRFgo motherboard with a nRF51422 DK attached (PCA10007).
I've installed all the tools of the toolchain as stated in...
