Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hi Nordic,
I test with nRF7002-DK and IC mark on nRF7002 is below:
N7002 QFAAB0 2252AA
Here is my test data, showing about a 3dB discrepancy between power setting...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I am working with the zephyr ZMS sample application. I am using SDK 2.9.0, and I built the application for the nRF54L15DK (nrf54l15dk/nrf54l15/cpuapp). The sample works...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
I have finished developing an application, utilizing the nRF 9151 DK, and I am now working on transferring the firmware to a custom board and testing it. However, when creating...
I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
