Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
Hi,
In trying to take the PPI example code from nRF5_SDK_17.1.0_ddde560 and adapt it to use RTC for an event-end-point, I get the following error:
Error[Pe020]: identifier...
*EDIT* - Using NCS 2.9 I am using the QSPI peripheral to communicate with a display.
1. I initialize the QSPI peripheral. I have tried both blocking and non-blocking. Both...
Hello everyone,
I am using the NRF5340-DK development board, but I am having trouble restarting advertising when my smartphone connects or disconnects from the board. Once...
I have created a barebones blinky example as a way to start developing for the dual cores on the nRF53, but I can't seem to synchronize them. The code on both cores is nearly...
Hi,
This is a followup on https://devzone.nordicsemi.com/f/nordic-q-a/119259/synchronisation-between-tx-and-rx-in-connectionless-direction-finding
We now have a synchronised...
I am using OpenThread network and working on CoAP Client and Server examples (Customized). Everything working fine when devices are on main power.
My client devices are...
I am running VSCode with the latest nRF extension. I am on v2.9.1 of the SDK
I created a new app and copied the bluetooth_st_ble_sensor sample project.
I would like to...
Hi,
I used the nRF52840 board with SDK v2.8.0 .
When we tried to build this example code, we encountered the following error: v2.8.0/zephyr/include/zephyr/device.h:92...
Hi!
S132, SDK17.1, nRF52832
Very strange behavior, I connected my central to the bonded peripherial success and got an BLE_GAP_EVT_CONNECTED event, but when I disconnected...
Hello,
I'm working on a custom board with a nrf54l15 chip.
I would like to add an interruption on the GPIO P2.10. But I get an error -ENOTSUP with gpio_pin_interrupt_configure_dt...
Hi Support Team,
I tried several ways to set the image version but failed. My SDK is ncs V2.5.2. 1. set(CONFIG_MCUBOOT_IMAGE_VERSION "1.0.0") in CMakeLists.txt: did not...
Recently I've had an issue with 3 of our nRF9160 based products during production (several hundred of the same hardware/firmware/SIMs work fine). The issue is that while the...
Hello Nordic support,
My application is a Zigbee coordinator application on nrf52840 based on nRF5 SDK for Thread and Zigbee v4.2.0. I was able to pair a Zigbee end device...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
I am developing a device that uses ESB.
Uses modules that are Telec and FCC certified with BLE profiles. (module : MDBT50Q-512K)
I have a few questions.
Q1. The TX power...
