Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello everyone, I hope you can guide me in a right direction. 1. I setup my environment as per https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/installation.html , using...
Dear support i have two problems,
In ncs 2.6.1 i get: error: '__device_dts_ord_DT_N_NODELABEL_red_led_P_gpios_IDX_0_PH_ORD' undeclared here (not in a function) in the...
Hi All.
I am trying to emulate a central BLE module to scan peripherals around, using an nRF52840 USB dongle and nRF Connect for Desktop. The goal is to confirm that my...
Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
Hi,
I'm trying to implement a Firmware Erase and Update procedure using the nRF52832 module on a custom board. In the Nordic Devzone I've been following the steps to do...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
Hi Nordic team!
Is there any way to dynamically change the charging current while the charging is ongoing? BCHGISETMSB and BCHGISETLSB can be changed only if charging is...
Hello,
We have an nrf522840 board using retained memory feature following this sample and using the NRF_RETENTION setting:
https://github.com/zephyrproject-rtos/zephyr...
Hi,
My project is based on NRF52832 with SDK11.
I got 2 working units, 1 is advertiser and 1 central.
The advertiser is advertising every 2 second.
The central unit...
Hi, Goal: Send a firmware update from nrf5340 to another nrf5340 over BLE I found the following sample and a lot of support tickets talking about this sample but I am unable...
Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
I am working with the DWM3001CDK board for Ultrawide band, but would like to use one of the free LEDs on (P0.14, P0.22, P0.05, or P0.04) as a way to show that the 3 AAs powering...
Hi,
We’ve designed a project using the nRF5340 + nRF7002 combination, with Wi-Fi connectivity enabled.
As part of our preparations for FCC certification, we’re currently...
We designed a nRF54L15 custom board and now want to add nRF21540 FEM module to our device tree as follows:
/ {
nrf_radio_fem: name_of_fem_node {
compatible = "nordic...
Dear DevZone,
While porting our project from NCS 2.9.1 to NCS 3.0.0, I ran into linker errors when building LVGL. The linker reports that it cannot find functions defined...
