In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I'd like my VS Code build configuration for my project to be included in version control.
It seems like this configuration is stored somewhere in the "build" directory that...
Description:
I encountered an issue where my NRF54L15DK development board fails to connect to my Windows 11 PC. Upon plugging in the board, the LED near the debugger starts...
Performing a DFU with an iPhone works in some configurations and fails in other. Android consistently works.
The failing version of iOS is:
iPhone 12 mini
iPhone 13...
I'm trying to connect a SIM800L to my nrf52840-dk which I power through 5V USB. I'm a beginner at electronics so just want to make sure I understand how to wire things, please...
Hi,
I would like to know what are the prerequisites to get the ICCID of the sim card:
This is the code I use, nothing special. I can get the IMEI of the modem but not...
Hello,
In nRF5340 I use one RTC and it works. Here is my code:
1) in prj.conf:
CONFIG_NRFX_RTC=y CONFIG_NRFX_RTC0=y
2) in the code:
a) define: nrfx_rtc_t sti_period_rtc_0...
Good morning,
I am using the nRF9160 as an AT command modem running the SLM app. I aim to set eDRX and disable PSM (PSM doesn´t make sense in our project). According to...
Hi all,
My team and I are evaluating some BLE modules available on the market. One of them is the UBLOX BMD-340, which contains the nRF52840-QIAA SoC.
We are encountering...
Hello Nordic Engineer,
I have already implemented a Mesh network using iOS nRF Mesh, 5340 DK, and 52840 DK, with the mesh_light example.
The NUS I used before was able...
I am trying to flash the Enhanced ShockBurst (ESB) example on an nRF52840 USB Dongle (PCA10059) . Since the ESB example is originally designed for the PCA10056 (nRF52840 DK...
Hi all, need to establish a CIS connection to an already connected BLE device with security level > = 2 . However when the ACL connection has security level > = 2 and the...
Hello, We're developing a project on a custom board based on nRF52832 and noticed that P0.20 is high on powerup, even with no firmware. Is there a way to controll the pin...
In the nRF5340 Audio DK example located at C:\ncs\nrf\applications\nrf5340_audio , I want to add a third board and communicate with it from the master (gateway) to send commands...
How can I read the whole advertising packet when are packets larger than some specific size? This is the issue. I want to read this adv packet:
But I only get this on...
we have 6 custom board with nRF52840 we are able to flash test codes in 2 boards , while 4 boards give
Error :No Cortex-M SW Device Found . this is in nrf sdk .
when we...
