I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I am working on zigbee demo "light_switch" with NCS2.8 Add-on SDK.I enabled MCUboot according to the steps in the course " Lesson 9 – Bootloaders and DFU/FOTA "
1...
Hey folks,
i have to use the nrf9160 board to create a PoC for a project of our company. The main topic of the PoC is not important here because i cant even connect to an...
Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello! Introduction. Responsibilities of the cores in my device: 1. app core. 1.1. data processing from a stereo microphone 1.2. data sending to net core. 2. net core. 2.1...
Hi
I need to sync a PC with a BLE board. Fixed delay is not a problem, but jitter should be max +/- 1 ms.
Our competitors have solved this issue some how.
As we all...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi,
I try to migrate a working nRF53 Zigbee project from SDK 2.7 to the latest SDK and an nRF54. As described here, I also switched to Zigbee R23. The project structure...
Hey there!
I'm trying to run the 'wifi/shell' sample on v3.0.1 on a nrf7002dk (targeting the nrf7002dk/nrf5340/cpuapp) with sysbuild enabled, of course and I'm getting...
Hi,
I am trying to set the Tx power level on the central device, I have followed the nordic example samples/bluetooth/hci_pwr_ctrl in the Zephyr tree. But it only sets for...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Hello, I would like to ask if the latest SDK version supports power management on the FLPR core of the nRF54L15. According to this article, the power consumption is quite...
I am using ncs2.9.1.
I am currently testing Bluetooth mesh dfu using 54l15dk. Now I want to put the firmware that is ready for updating into the external flash of the distributor...
