Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
I am working through BTLE Fundamentals, Lesson 6, Exercise 2, and running the code from blefund_less3_exer2 per the instructions and it all looks good on the app COM log:...
Hello! I am currently developing my own custom service with two nrf 52840 development kits where one acts as the Client and one acts as the Server. I have managed to set up...
Wheh I try to debug a multi-domain-image on an nrf5340 or 52840, I can debug the mcuboot domain just fine. But when I try to debug the app-domain (I tried this with the zephyr...
Hi,
Using Visual Studio Code, when I build asset_tracker_v2 in NCS v2.9.1, for nrf9160dk/nrf9160.ns, I keep getting the problem shown in the subject line
equivalently...
Dear Team,
I have a question regarding preventing LTE from endlessly searching for a network connection. Lately I have been facing issues where LTE connection is rejected...
Hello everybody! It's my first question and I'm new at mcu programming. I hope for your understanding!
I have a task: count seconds using a counter and display them on a...
Hello,
I'm working with a custom board using an nRF5340 as its primary MCU and NCS 2.7.0. The application I'm developing requires internet connection and can ideally support...
Hi!
I am trying to power the thingy:91 from solar panels and have some issues with the thingy:91 restarting when the solar panel receives a medium amount of light. The solar...
nRF Connect SDK Toolchain v2.4.2, Windows 10
Hi,
We're running low on RAM on the nRF5340 application core, and I'm looking into ways to recover RAM both from our application...
I downloaded https://github.com/NordicDeveloperAcademy/ncs-inter/tree/main/v2.9.0-v2.7.0/l8/l8_e1 and tried to build it for nrf54l15dk/nrf54l15/cpuapp/ns . There are several...
Hello
I am running the nrf/samples/bluetooth/direction_findinding_connectionless_rx App on an nRF52833-DK with nrf Connect SDK 2.2.0
I have set VS Code to use board...
Hi All,
I came across this thread regarding programming external boards. ( https://devzone.nordicsemi.com/f/nordic-q-a/14058/external-programming-using-nrf52-dk )
In order...
Hello,Nordic team
I am programming with nrf52833 and ncs v2.9.0
While bonding with peripheral ,central report No memory to create new report.But my soc flash and ram are...
I work on nRF54L15DK.
When building for the nRF54L15DK, only 188KB of SRAM is allocated. The remaining 68KB seems to be allocated to the FLPR MCU. How can I change this...
