Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
I have made custom nrf 51822 board, I don't have LFCLK crystal i.e, 32.768khz. When i run ble_hrs example code in it , current consumption of my board goes to ~150uA...
Hi
In my application I need to transfer several paires of bytes to a slave device, and it's mandatory
for CS signal to go high between pairs. (This actually means I have...
Hi
I want to know why flash memory access should be scheduled in between the protocol radio event?
is there any relation between the flash access and radio opeartion physically...
Hello,
I am developing a wearable device that utilises nRF51822. Right now, I am having a problem because when the wearable device is connected to a new phone, it needs...
Dears,
I am designing a notification application. I would like to know what if I want to support both of iOS and Android phone, which example code of ble_app_alert_notification...
im following ( devzone.nordicsemi.com/.../) step to "Setting up a project for debugging in Eclipse"
i run the debug config and click suspend
then get some problems
...
Hi guys, I just want to share my iBeacon code (over s110) developed on nrf51 dev board under ubuntu. It works fine but please feel free to improve it and share it!
I developed...
In some case sd_nvic_SystemReset() can not reset?
nrf51822 S110.
for example:
void main(void)
{
sd_nvic_SystemReset();
do something;
}
It can do somthing!!
So sd_nvic_SystemReset...
Hi,
I have just bought NRF51822 without any extra peripherals(no motherboard/DK). Just plain Module like below image.
I am supplying 3.3V to VDD and also Connected GND...
Hi all,
I find a problem when testing the ANCS program. It seems that after you connect the device with ANCS with an iphone, you cannot connect the device with another iphone...
I built the ble_app_proximity project and down load into my board, it can advertise and can connected by the lightblue and the nRF toolbox, But i sent the hex value of 0x02...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
Hi,
I am currently working on a project with nRF52 preview DK.
In my system, an ECG chip is used to measure the heart rate and the data will be transferred back to nRF52...
Hi,
I have a number of products with nRF905 successfully deployed. Now, I am in a little struggle with a new one. The problem is the signal strength. The other products...
I'm trying to add a feature where my peripheral will temporarily trigger a Faster Connection Parameter for a period of time determined by an app_timer. However it seems that...
