I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi everyone,
I am using the Arch BLE running firmware version 221 (most current one).
Whenever I create more than 3 PwmOut objects (from the mbed library), the MCU just...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I think I have followed everything from:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
to convert the dual_bank_serial_s110 to an S210 serial bootloader...
Hello
I’m trying out the new nRF52832 (QFAA-AA0) with preview kit pca10036. I have S132 softdevice installed and running the beacon example from SDK 0.9.0 which appears...
Hi,
I am using the sample BLE_gls code provided by Nordic.
I have made the following changes in the code:
#define SEC_PARAM_MITM 0
#define SEC_PARAM_IO_CAPABILITIES...
Now I want to store some data above bootloader( the address after bootloader), but every time when I call the function pstorage_init(), the function will defaultly set my...
How to add single 128-bit characteristic uuid. It's not based on service uuid.I have tryed the link text ，It's work,but it's something wrong .
I am working on ios ble midi...
I developed a custom board with nRF51822_xxAA on it, working on low voltage mode.
I can program some basic things on it using Keil uVision 5.15 and a J-link to flash the...
Hi,
I'm trying to use the pstorage on a central device.
An event of BLE_GAP_EVT_ADV_REPORT is called by discovering some ble devices while a central device is scanning...
I have a nrf51-DK, SDK 9.0, S110, dual-bank bootloader that supports both serial and ble protocols, developed using GCC/Eclipse. My application uses the watchdog timer. I...
Hi,
I'm developing an Android application that uses Android DFU Library and I want to set the number of packets that are sent every notification interval to 1. I couldn...
On the BMD200 evaluation kit ( www.rigado.com/.../) using the nrf58001:
--> UART TX (pin P0.09) works - confirmed with logic analyzer and Serial Port Terminal on the PC...
We are operating on nRF51822 QFAC with S130 SD. We have a functionality where the device switches between scanning and advertising. Strangely we have observed that after few...
Hi,
When i read the ble_peripheral sample of the SDK, i have a question below.
If my peripheral is connecting a central, then i use function sd_ble_gap_disconnect() to disconnect...
Hi,
The established time tick source for FreeRTOS is RTC1 via the APP_TIMER module. I am trying to shift the basis of the APP_TIMER from RTC1 to TIMER2, so that I can use...
