Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
We are using nRF51822 BLE device in our product. As we got to know that this chip cannot be factory programmed.
Can you please suggest us how we can program this...
Does the following flasher also allow to debug the nRF51822 device?
Segger Flasher Portable
If not... which flasher/debugger is suitable to be used during development...
I'm adding the bond manager to an existing nRF51822 s110 soft device project to enable encryption when reading/writing certain characteristics of a BLE service.
As far...
i am making something about dfu!
i read some message from "readme.txt"
such as :
Program initial SoftDevice
Make sure the device is cleared (nrfjprog --eraseall...
I have trying my best to find the url of ''nrf51_sdk_v6_0_0_43681.msi'，but there is nothing i got, i need some help.
Do you know somthing about it? thanks!
Edit: One...
Hi,
We're using the SPI to communicate with a device that, when powered up, supports only up to 3Mbps SPI frequency , but after a while can work with higher frequencies....
Hi,
We have a customer requirement that he want to setup the ANCS service bypass pairing. It looks TI CC2541 could do so as below URL. Do you think it could be done from...
Hi. We're looking at nordic modules for a range of new miniaturized health sensors.
Does anyone know how to compute the current consumption of a BLE module given the data...
Hi!
I've quite wired problem with PWM based on NRF_TIMER.
When I modify CC value to adjust current value to desired value slowly (function is fired from outside event...
I have written application similar to ble_app_temp (posted by Ole Morten) and during the test I noticed that current consumption is extremly high. I used brand new coin battery...
I have writable characteristic on the server. As far as I understood there are at least two ways to access to its value: one using ble_evt_t and BLE_GATTS_EVT_WRITE another...
Hello,
i have seen here a extended version of Spi-Master driver:
devzone.nordicsemi.com/.../a00006.html
With funktions like:
-spi_master_send_recv();
spi_master_get_state...
I'm using the reference design for the WLCSP nRF51822 package, and I noticed that there are 2 pins (G3 and G4) that are listed as N.C. (No Connection) in the product specification...
