Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi nordics!
First of all, thanks for answering my questions before.
Now, I want to generate a clock(48 pulses) with 200us width.
However, sometimes the width of...
Hi ,
I have a application program which uses s110 and UART service .
The issue is the program is not working when I enable the Micro Lib in keil.
On observing the map file...
Hello,
I want to use flash for logging sensor data and sending via BLE.
I found several APIs for store data to flash.
pstorage (Persistent Storage Access Routines...
Hi all,
I would like to know how can I program and debug the nRF51822 development boards?
I've seen some boards have a built-in programmer and others haven't.
How can...
In the DFU code provided by nordic is explicitly states that.
"Soft reset from application must not reinitialize the SoftDevice."
In my application I do not have a button...
Hello,
I have made simple modifications to the multilink central and peripheral examples, adding an additional button and notification characteristic. Things have been...
We're designing a board with the nrf51822 QFA part. Due to design constraints, the chip will have to be about 15mm from where the antenna port will be. The routing to the...
Hello!
I am an electronics engineer in my company, but I'm not familiar with wireless design.
My company will launch a project that will use wireless connection for bidirectional...
hii i use nrf51822 dev kit, and want to know the status of that is that right now advertising, pairing, connect etc. so is their any function that i use to check the status...
Hi,
I'm planning to use an external MCU to process my digital signals and send it through nRF51822. Do I need to develop an on-board antenna? TI has the module CC2541 from...
Hi,
Recently S120 v2.0.0(either Peripheral or Central) is officially released, but it seems not still listed on BT-SIG Qualification.
I can see that Sx20 host layer QDID...
Hi,
I have loaded the NRF beacon app and it's wonderful that it has a tasker integration. I need to push simple REST commands on discovery of NRF51822 beacons by this NRF...
In the examples such as the hrs, if bonding is enabled by:
#define SEC_PARAM_BOND 1
does the SD automatically save the bonding info the first time it bonds, and then restore...
I would like to program an external flash using SPI during production and I was wondering if there is a tool available already or if Nordic can put this feature into nRFgo...
