Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'm using nRF51422-QFAA E00 with S310, nRF51 5.2.0
When I configure ANT channel as a Master with Network number 0, all works OK. But if I try to set different network number...
50ms_measure_30ms_other.jpg
Attached is current measured using the s310 softdevice
Every 50ms timer takes a twi measurement, which is a twi 6 byte read followed immediately...
I am trying to write a bootloader that will work with the S120. Both the examples seem to only work with the S110, so they don't help much. I already have the binary I want...
Hi,
we can send data from server to client by sd_ble_gatts_hvx() in ble_app_hrs but:
1.How does the client receive those data?
2.How dose the client send data to...
I have two boards similar to www.aliexpress.com/.../1862953539.html
openocd on one board shows:
Info : nRF51822-QFAA(build code: G0) 256kB Flash
and on the other...
I need my device in some conditions to create an alarm which will be readable for any BLE device in range. Is it possible? What is the right way of doing so?
Thank you.
Dear all,
I am following the user guide nRF51822_Evaluation_Kit User_Guide v1.2.pdf
When I try to compile the example
C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001...
Is there anywhere I can buy just a J-link Lite? We have a couple of developers working on the nRF51822 and I need to get some additional debuggers, and would rather not buy...
I am using the app_button to handle all incoming button presses. On a press detection I trigger an app_timer which handles tracking how long the button has been pushed, and...
I just starting out trying to get an Eclipse dev environment up and running. I've tried following nAN-29 but it seems out of date. The issues I run into are:
CDT...
Hi,
First I want to thank all nordic staff for their great work on sdk & this incredible tiny chip that do a lot :-). I play a little with the devkit sample and my nrf development...
I've got 3 of the 51822 kits: smart beacon, m-kit, and eval-kit.
I've successfully installed Keil uVision 5.1 and developed/loaded applications for eval-kit.
I've successfully...
I'm just trying to determine if I get full SDK access with the nRF51822-mKIT; or if that requires nRF51822-EK/DK? The current posts on the boards seem to be conflicting in...
