hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
nrf52820 custom board
nRF5_SDK_17.1.0_ddde560
s112_nrf52_7.2.0_softdevice
secure_bootloader_ble_s112_pca10100e
I tried to incorporate ble dfu to my application but...
I just needed some clarification as I'm migrating from SDK 6.1 to SDK10:
app_button: There's no way to have the Button function thru the Scheduler anymore. I would...
i am using latest "master control panel" v4.0.5 and latest "nRF tool box" v1.16.2
and use sdk 5.2(its compulsory)
soft-device s110 v6.2.1(its compulsory)
and PCA10028 with...
Hello everyone,
Could anyone tell me which pins are the programming pins of the nRF51822 chip for a QFN48 packet ? How can I program it on my custom PCB?
thanks..
We are planning to use nRF52 for its superior computing power in an application. Unfortunately it appears that the throughput is more limited than on nRF51. Since we need...
Hi,
I used two 51822 modules for my project. One should send a byte and other one should receive.
I used the exact same configurations of radio examples (transmitter and...
I am trying to read an analog value on the GPIO port into my application. Looking through the examples, there aren't any that help solve this problem as the ADC example is...
I have tried to follow the installation instructions and have installed nRFGoStudio, the Keil MDK-ARM, and downloaded the latest nRF52 SDK. I also installed all of the device...
Hello,
Iam a beginner to NRF51 and Iot.
I want to be able to send messages from raspberry pie to NRF51 dk and vice versa via Bluetooth.
Iam using a generic Bluetooth dongle...
Hi ,
I've just started using a Nordic's product : an nRF51 422 QFAC develepement Kit
I was running tests by loading examples on this board when I lost the connection between...
I am building my application up on the blinky free rtos. I want to use RTC and ble stack. i am initialising RTC1 first and ble stack stact.
The problem is that I am getting...
I am using nordic nrf8002 BLE with a breakout board & not a developement kit. I gave 3.3v supply in different combinations:
(1)3.3v to vdd pin-1, GND to vss pin-4
(2)3.3v...
Is any SDK available which has single bank BLE DFU bootloader source code?
If No then is it possible to convert dual bank BLE dfu bootloader into single bank BLE dfu bootloader...
I am trying to Migrate from Sdk 6 to Sdk 11 .
Here i am facing problem in discovering Custom Characteristics .
I can successfully add service and 2 characteristics without...
Hi!
I'm building an application with one custom service containing a few characteristics, all of which are to be indicated upon. When using the Master Control Panel Android...
