Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Dear Nordic Semiconductor Team and Community Members,
I am currently working on an nRF54L05 project where I aim to use only the primary slot in MCUboot due to memory constraints...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
I've been working on a custom device utilising the nRF52832 that needs to switch GPIOs in tightly controlled pulses. The problematic section is part of a much larger project...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hello, my application requires very precise timing to trigger an action on the edge of the GPS time. I just need to get this time once in a while to synchronize the system...
Working on the nRF52833DK board and based off the nrfx_spim_spis advanced non-blocking example sample. I've already converted the SPI master to use the Zephyr driver instead...
Hi! We are having problems pairing a nRF52840 against linux (ubuntu 25.04). Pairing fails instantly, before any passkey is shown on the host, returning with code 9. Short...
Hi,
I'm half way through the Cellular course on the dev academy and although I am able to connect to the Nordic and Hivemq publich brokers, when I attempt to connect to...
