I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
hi,
I have been reading some posts regarding similar issues, but I am not able to nail down this one.
I am trying to create a custom 128 UUID and associate some Service...
I overwrited the application program which made with v5.1.0 and it included only difference against the v5.1.0 to sdk v6.1.0. After this, I buidled it but the target didn...
I am looking for a dev kit which would allow me to try out SoftDevice S130, will I be able to use S130 if I buy any of these:
nRF51822-mKIT
nRF51822 DK
nRF51822 EK...
The nrf51 reference manual shows timing diagrams for the TWI interface when reading from slaves to have a shortcut between BB and SUSPEND. My assumption would be that's there...
I am using the ble_app_uart code from SDK 6.0 on my custom PCB with a nrf51822. I am comparing it's functionality with a PCA10004. Both are running the exact same code. I...
Hi all,
some time ago we bought a nRF51822 Evaluation Kit with the PCA10001 being Version v2.0.0.
Why exactly is it not recommended to work with the new SDKs such as SDK6...
Has anyone played with getting the iBeacon reference kit/software to run with the SD7.0 code?
I'm wanting to change from the boot loader + SD 6 + app to a simpler SD 7...
I have download the puck-central-android code from the following link
github.com/.../puck-central-android
I can build the project and successfully programmed in the android...
hi.
as far as i know, dfu for softdevice 110 can be carried out over ble, while s120 can not. so i have to implement a bootloader for an app with s120 through wired.
is...
Hello to all,
Since a couple of weeks I have a problem in a program which consist of three parts:
1.- a Timer to make a pulse train by interrupts
2.- a program to control...
Hi,
Im using SD5 and after some time (every time different) of transmitting HRS data the SD stops apparently, because there is no more connection with my Android phone...
I am trying to apply the new features in the latest soft device s110 v7 to the firmware of my pca20006 bluetooth smart beacons (nRF51822 Bluetooth Smart Beacon Kit Firmware...
I have Eclipse CDT set up for debugging the ble_app_proximity sample code on a Mac. I can start the GDB server on the console and connect to it. Flashing the code seems to...
Do you a way to get better range for BLE.
Distance outdoor Number of samples per second using the development kit. ( 12 bytes)
15m 100 samples
40m 60 samples
50m 50 samples...
Reading the s110_nrf51822_7_0_0.migration document there's a small section which states that due to an issue in the release you need to do the following ..
sd_ble_gap_enable...
