Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
I can see, that sd_ble_gatts_hvx() returns 13313, if the notification is not enabled for that characteristic from the connected central. --> S120 Softdevice runs...
Hi
I got my new NRF51 DK. I was able to test it with blinky using mbed. I had to add the add the device nRF51-DK. then compile it and drag the .hex file into the mbed drive...
When I first got the nRF51-DK board... I was able to see this board on nRFgo. I then added the s130 hex file to it.. Since then when I connect this board, it does not show...
Hi,
Everyone,
I am trying to achieve minimum current level, I can possibly achieve, with continuous BLE transmission
so, I tried running BLE_POWER_PROFILING_APP given...
Hello to everybody.
I've buy a nrf51822 module with a motherboard.
i struggling to programming an uart over bluetooth example but i think something missing.
With nrfgo...
We configured nrf24LE1 as PRX and nrf52 as PTX and the packet sent out every seconds.
The nrf24LE1 will only received the packets every twice packet sent out and both packet...
I tried to use difference Data Rate for testing the transmit distance. Don't know why using the 250k bit is worse than using the 2M bit & 1M bit. The distance will decrease...
I am debugging a small program for the nRF52, which uses the App Timer and communicates over UART. I am trying to keep up with bug fixes, and so I'm using SDK 11.0.
The...
We have an application that requires a fairly quick disconnect (under 250msec) when the RSSI exceeds a threshold, for example -80db. Unfortunately, around 1 out of every 4...
I am trying to program a nrf51822 module using the nrf51-dk.I have made connections as per the nrf51-dk user guide, but sme is not working...
I am using the Vdd of the...
Hello all,
In a network of sensors with power constraints in a room which protocol is the best?
Newer devices seem to use BLE but I don't want to discard good old nrf24l01...
HI, I try to turn on the OLED.
I can not confirm that the lights turned on
I want to change background color.
What should I do?
Currently being output as shown...
I have installed Keil v5.18a
and have installed MDK for nRF51-DK.
Examining the basic LED blink examples showed that in some projects, the 'bsp.h' which would be the header...
I just setup Eclipse and trying to compile.. I was getting warnings.. I think I have installed all the relevant packages.. But still getting following warnings. Am I missing...
