Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hi,
I'm trying to connect the nrf51822 chip to an ethernet (W5500 module). For the moment, it fails without error (nothing works).
So I start from a simpliest program...
I am finding that bonds are not saved to flash when using the latest SDK and S110 SoftDevice.
To test this, I am using the HTS example code, and the Master Dongle.
I open...
Hello,
I discover and connect my nRF51822 service. It can be peripheral and Communication read/write data. but have some issue for disconnect/reconnect .When My app for iOS...
Hello,
I am planning to develop a system where there are 16 bluetooth LE devices (nRF51822) each one sending/receiving data via Bluetooth LE (~30 kbps) to/from an access...
Hi !
I know that there is a way of OTA updating the nrf8200 application. But i'm not sure if this process requires aditional hardware like it happens when using the BLE113...
Hi All,
I am able to successfully connect to nrf51822 EK using BlueZ 5.12 and can read many of the characteristics except for the temperature value.
I understand that...
Hello
I have a project about voice communication.
Trying to do bidirectional voice communication, is there any possible to work on nrf51822
It means whatever via Bluetooth...
Hi,
I have version 2.0.0 of Evaluation Kit. I was waiting for the new SDK and SD 6.0.0 but I have seen the warning about hardware versions. I have to finish a SoftDevice...
I'm a noob in this alley! it is my first time working with Nordic products. In the past I used Energy Micro and ST Micro.
I downloaded Keil 4.x from ARM website. Then I...
Hello,
I am developing a project using nRF51922 and S310, and the project is built using SDK4.2.2 with the modifications mentioned in a document called "nRF51922 - ble...
We are looking to understand the internal working of the nRF51822 firmware (MEFW_nRF51822_0.9.0_firmware.hex). If someone can share the original code or the basic block diagram...
Hi folks,
I want to match my IFA PCB antenna to the nRF8001. As Harald recommended a couple times, I am going to measure the antenna of the final PCB with a Vector Network...
Hi All,
I use the 51822 DK to do the current measurement and do as the DK user guide 5.1.8 current measurement.
I just use the __WFI() to make the 51822 get into idle...
Hi!
I must match NRF24L01 to 40+j48 ohm antenna. This is not my design, so
no possibility to change. I have PCB antenna, that was measured to be 40+j48 inside
enclosure...
I have some non-volatile storage routines that I have written before, but the new SDK V5.0.0 has this pstorage module that is supposed to replace it, right? How do I migrate...
