Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I am wanting to talk to this external 1Mbit RAM chip through an SPI interface: https://www.microchip.com/en-us/product/23lc1024 with the nRF5340 device. Preferably,...
Hi,
I am trying to use the clangd extension with nRF Connect SDK, as it does a much better job than intellisense. I added
set (CMAKE_EXPORT_COMPILE_COMMANDS ON )
...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
I have read info somewhere which said there is method to crack the protection just by setting UICR APPPROTECT register.
I want to know if Nordic has upgraded the protection...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
I want to create automatic build using CI in bitbucket pipeline.
I would like to use image NordicPlayground / nrf-docker to compile the project. I saw the article Build...
Hi everyone
I have installed the nRF Connect for VS Code Extension Pack later tried to install toolchain the latest is v3.0.2 it successfully installed but im not getting...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
Hi,
I want to use nPM1300EK、nPM PowerUP (official v2.1.1) profiling a chargeable battery, whose rated capacity、standard charging current is 2000mAh and 400mA respectively...
Hi Team,
we are using two nRF5340 Audio DK kits to test LE Audio CIS example (unicast client & server).
kit1 nRF5340 Audio DK - act as gateway ( connected to PC/shared...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
