Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I want to use the nrf51822 to communicate withe the old module of 24l01p, in the module of 24l01p, the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch...
Hello,
I've been trying to get my TWI device working in conjunction with the BLE stack (i.e. s110 softdevice is enabled) on a nRF51822.
I found another thread with an...
Hi,
I want to use the 51822 to receive data that from the module of 24l01.the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch[2] = 0xe3;
addrofch[3] =...
Hi,
Can any one tell me, what will be the current taken by internal flash of Nordic for
write and read operation and what will be the max time nordic will take to write...
Can someone familiar with the nRF51822 timer infrastructure confirm for me what the maximum achievable PWM frequency is, assuming 8-bit resolution? I've been weeding through...
We got the new sdk and ported the "Alert Notification Profile" to the EVM board. It can communicate with the the Master Control Panel. We want to know whether it can communicate...
hello, on my board the nrf24l01 is optional.
what is the preferred solution to identify if a nrf24l01 is present.
I tried to read the status register. But sometimes...
I am using Laird Bluetooth-4 device BL600 with smartBASIC. While communicating over the I2C bus I am encountering the Hard Pull-up on SDA line. During the Slave ACK I could...
The new pstorage abstraction is almost using 1K RAM, which I'd actually planned to use for something else :-)
Is it possible to limit the RAM used by this module. Can I...
Hi there
can I download the source code?
This app is able to detect the nrf51822 chip even with android 4.1, which is great, so I could test my firmware on my samung...
Hi,
We have a custom board with nRF51822 chipset, We have developed the code to work with some senor peripherals, everything is working fine, but sometimes, when we do testing...
Hi:
chip:nRF51822
code:ble keyboard
How to send the VIRTUAL_CABLE_UNPLUG request by Bluetooth HID devices?
If Virtual Cable Unplug is received by a Bluetooth HID device...
hello，
the datasheet of nRF2460 “nRF2460_Product_Specification_v1.0” has a explanation “the MCLK signal on the ATX side is locked to the
reference （crystal）of the ARX...
