Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I've got an nRF51822 development kit that I'm trying to get started on. I've gone to Kiel and downloaded uVision 4 (mdk472_a). I install it with all default settings and it...
Hi,
I add UART support using IRQ on the "ant_hrm_tx" example code.
and I'm sending packet of 4 bytes that contains: Delimiter,HeartRate,Battery,Delimiter
the frame...
Hi, I am trying to test my UART using some simple loopback test, and I have noticed that the service discovery command of BLE will occupy the CPU a quite long time. I am just...
I was unaware that the 'manufacturer data' in the advertising packets is limited to less than a full payload. However, whenever I set it to >6 the program "crashes".
...
When I use keil to download the software to the chip, there are two questions:
like attached.
2.NRFGO CAN'T SEE J-LINK LITE CORTEXM BOARD
Is there any way to solve...
We have recently moved to a new PCB which puts the nRF8001 on the layout instead of plugging into a nRF2741 development module. The nRF8001 connects to a TI Cortex-M4 Tiva...
Hi, we would like to create a kind of game using 2.4Ghz emitters . The 2.4Ghz USB Dongle emits and the mobile phone detects the frequency + embed unique ID/code so we confirm...
To be more detailed:
One of my ADC pins will be connected to another device that could be providing a voltage of about 3V, but through a 100 kohm resistor. (actually it...
Dear Nordic Developer Zone,
Since I have implemented a timer with interrupt in my application, the debug mode if the Keil IDE stops working when I try to restart the code...
Hello, I'm trying to develop with the nRF51822 Eval kit and GCC and Eclipse. I've been getting some strange behavior and errors lately. I'm not really sure how to describe...
I'm a green hand HW Engineer.
I'm trying to compile, program, and run The Heart rate monitor demo though following the step in nRF51822_DK_User_Guide_v1.0.pdf .
First...
Hi Nordic devzone,
For the nRF51822 device, I would like to know if there is any internal pull-up/pulldown resistor on SWDIO and on SWDCLK (although a 12 K-ohm pulldown...
Is it possible through the API/Softdevice to do one of the following:
read out the current advertising data structure, change a the manufacturing data field, and...
