Hello, Have some experience with embedded development, but new to nRF Connect, sysbuild, Kconfig etc.
Using Windows host VS code with nRF Connect extensions - current versions...
HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi, having some issues with the matter door lock sample for the nRF54L15DK on NCS 3.0.2. I'm getting strange failures on boot when running the default matter door lock sample...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
Hi, On the nrf54L15 with MCU boot enabled, what is approximately the fastest time that the chip could boot and set a gpio line high, if everything not critical is disabled...
i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
Hi Support Team,
I want to use an external flash(2M byte) to store the sensor data in a 'circular overwrite' way. I now tried it with the FCB(Flash Circular Buffer) on nRF5340...
I am currently reviewing Zigbee for an upcoming project using the nRF5340DK board. The build environment is nRF Connect for VS Code Extension Pack, and I’m using SDK version...
Hello,
I've developed a PCB that connects an RTD (PT100) to a Wheatstone bridge, set to 100 ohms at 0°C. The bridge terminals (as seen in the diagram) connect to AIN4 and...
Hi everyone,
I am experiencing an issue with my custom board configuration for the nRF9151. When using the same code that works with the nRF9151 DK configuration, I encounter...
Hi there!
May I know how to have UART00 on P2 like what is shown below as I wanted to have higher speed.
Is it the same as other UART assignments on P0 and P1?
Thanks...
I am using VSCode with the nRF Connect extension (latest) and SDK 2.9.1.
I made my new app from the Bluetooth Peripheral sample.
When I try to debug I get the following...
I am using VSCode with nRF Connect extension with the 2.9.1 SDK.
I am trying to write my own device driver for the Zephyr OS and the TI CC1101 chip. Since the tutorial isn...
Hi,
nRF52832, SDK 17.1.0 with Softdevice S132.
Softdevice sleep does not work when advertising. Application flow is to advertise one packet, then go to sleep for X seconds...
Hello,
I use a PKK2 for power measurements on a nRF9160DK and Feather nRF9160 from circuit dojo. With the UDP example to test it out the sleep current so I can determine...
Hi Sigurd,
I'm finally using the mcuboot and mcumgr_cli I worked on in summer of 2023. I generated the mcumgr_cli for debian with go lang back then. I'm building my app...
Hi Nordic team,
We are currently investigating how to ensure that the fuel gauge continues learning and retaining the battery's charge/discharge profile over time.
In...
I am using Zephyr 2.9.0 with the sdk-nrf repo v2.9-branch checked out. The locator_tag sample builds without issue and flashes to the nRF54L15-PDK without issue. I have a...
I'm trying to use raw packet transmission (IN combination with wifi promiscous mode and raw sockets eventually) with my nRF WiFi device. I have both the sample raw_tx_packet...
Dear DevZone,
I would appreciate your assistance in understanding how to correctly configure Wi-Fi and BLE coexistence for the nRF5340DK and nRF7002EK with SDK version 2...
Hi! I'm testing the application with the custom Battery pofile I generated with nPM PowerUP app. During testing I found the issue with the SOC value calcultation depending...
