Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
I recently bought PPK2.
But am unable to connect it to my Linux PC with Power Profiler v4.1.0.
Below is the log -
08:49:26.328 Error: Failed with exit code 1. Failed...
How can we connect the Thingy:53 to the PPK2 using the included PCA64142 current measurement board, for both Source Meter and Ampere Meter modes?
The PCA64142 board...
Hi, I am seeking assistance with a very weird issue encountered while programming an nRF5340 SoC using a custom debugging-PCB using a SEGGER J-Link EDU debugger.
The debugging...
Hello,
We use nrf54l15dk + MX25R8035F external flash to do the matter development on NCS2.9.0, and we meet some problems:
1. when the matter.ota is 1003KB, takes about...
Dear forum, I am testing out the radio on the nrf5340 using two evaluation board connected to a SES setup, but the receiving board only gets garbage and the checksum is never...
Hi all,
I have a custom board with an 9151, I want to use mqtt with aws, it's works I'm able to connect aws, but I have a question about
If I want to be able to connect...
Hello Nordic Team,
I am requesting clarification on the capabilities of my nRF9151DK to be used as a debug and flash probe (via the 'debug out' P20 headers), and compare...
I am developing a new architecture for my project. So, I am getting data from the peripheral, a custom nrf52832 card. Also, I create my custom service to send data and add...
I installed NRF connect I successfully built project when I flash I get success, but actually I can see project is not flashed what and how can I debug that ?
I am receiving the above error when trying to create a destination under "Device Management -> Message Routing Service -> Add Destination". There is no further indication...
I've recently encountered a problem where the Device Tree Visual Editor no longer displays any peripherals (ADC, UART, SPI), making them uneditable. I have had my own board...
Hi everyone,
We found that the LIS2MDL_INT interrupt from the compass on P1.06 affects communication between the app core and the network core.
About 3 seconds after...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
