Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
I use NRF54L15 DK to develop channel sounding feature on zephyr SDK or nRF connect SDK.
How to configure CSTONES related registers to transmit and receive CS Tone packets...
Hello,
I’m working with a custom board using the nRF54L15 and the latest Nordic SDK, and I’m facing an issue while trying to communicate with an nPM1300 over I2C.
Here...
Hi all,
I'm working on a project with an nRF52840 using the nRF Connect SDK (version X.Y.Z) and Zephyr RTOS. My goal is to achieve maximum possible range for non-connectable...
nrf modem: 1.3.4
sdk: 2.3.0
Custom board.
We have an asset tracker that caches events when out of connectivity zone. We can accumulate 10-100 messages depending upon...
Hello!
I have designed a custom board with the nRF5340 , powered at 1.8V. I am able to program the chip successfully, but after the firmware is downloaded (Zephyr RTOS,...
In my application we have an nRF514L configured as an SPI target. Page 830 of the nRF54L datasheet (version 0.8, dated December 2024) documents that the SPIS peripheral requires...
I'm trying to convert some code from ESP32 to nRF, and I'm having problems with the microphone input. Mind you, I'm a beginner with nRF, so I'm sure I'm missing something...
Hi,
We want to enable zephyr shell over RTT on our custom board based on nrf52840. I tried the 'shell_module' sample with prj_minimal_rtt.conf and it works fine on nrf52840...
Hi there,
I built a battery powered custom PCBA with the NRF54L15 and the nPM1300. All the configuration and register work via I2C seems to be working properly (reading...
Hi. I have a working IAR project based on the nrf52 SDK \nordic\examples\ble_peripheral\ble_app_uart. i am attempting to port the project to ARMGCC using VSCode. I am at a...
Hello. I try to create a remote control for GoPro using nrf52 ble.
Using sdk 17.1 examples I can connect to GoPro and try to get a list of UUIDs. But I only get one UUID...
Hello
I'm using the settings partition to store user configuration data. I know that the BLE stack also uses it — particularly for storing bonding information — but I don...
Hi,
I am working on a project with nrf52832 and LIS3DH for a beacon.
I have added the low power feature into my application to go to standby mode in case of inactivity...
Hello Everyone,
I am using a nrf54l15 for my current project and ran into some discrepancies within the documentation provided for the processor.
Even the AI chat bot...
Hey I was working on starting sample code of wifi in ncs v2.6.1. When I added the correct ssid but wrong password in the prj.conf to check the status of the connection failure...
