I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Hello!
We have a project where we are using the nRF52840 with the ADS7052 (an ADC) on the SPI bus. We are using Zephyr 4.1.0, but I guess its same same with nRF Connect...
I have a LIS2DW12 accelerometer connected to nrf52840 SPIM3, and I am seeing an intermittent failure. In some instances while collecting accel data during a data ready interrupt...
Hi,
I believe the default application on Thingy91x uses LTE-m to connect, which is working fine. How do we make it use only nB-IoT?
For Thingy91, there is a guide
Getting...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
Hello. I'm trying to improve the permit join-handling in our project. Right now we're simply hammering the zBoss stack with bdb_start_top_level_commissioning( ZB_BDB_NETWORK_STEERING...
I’m using nrfjprog version 10.12.1 and JLinkARM.dll version 6.88 . I encountered an intermittent nrfjprog error when programming firmware to the nRF52833 .
In most cases...
I am trying to integrate nRF7002 into my application firmware, by using the "wifi/sta" example in NCS3.0.1.
My application has CONFIG_NRF_SECURITY=y and PSA enabled and...
Hi,
I am trying to use mcuboot to load a version that is stored in my external flash, and I cannot get it to boot. My project is being built using sysbuild and my target...
Hello,
I am trying to use an sdcard with the nrf54l15 DK board with the 2.9.1 sdk. However I encounter "<err> fatfs: Storage init ERROR! error: -134" when calling the disk_access_init...
hi i have a question
i ues ncs 2.9.0
This is the code that displays my Bluetooth connection
——————————————————————————————————————————————————
struct bt_data ad[]...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hello,
I’m working with a custom board using the nRF54L15 and the latest Nordic SDK, and I’m facing an issue while trying to communicate with an nPM1300 over I2C.
Here...
I am trying to run the debugger from the nrfconnect extention for viual studio code. for some reason It doesnt work, It seems to flash the app fine, but then this message...
Hello Team,
I’m working on creating a custom Matter cluster using the instructions provided in the Nordic documentation: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
