Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with two specific exercises: l2_e3 and l4_e1 . Other...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
Hello ,
I've been trying to build the wifi shell example sample for my nrf52840dk with a nrf7002ek shield. I'm setting the shield via CMakeLIsts ( set ( SHIELD nrf7002ek...
Hello Nordic Technical Support Team,
I'm developing a low-power product and considering using the nPM1300 PMIC. I have some questions regarding the system design:
Can...
Hi Nordic team!
Is there any way to dynamically change the charging current while the charging is ongoing? BCHGISETMSB and BCHGISETLSB can be changed only if charging is...
Hello,
I posted this in Zephyr's repo at first, but was told to post it here since I am using NCS.
I am running cellular modem sample on nRF54L15 and have it interfaced...
Hi all,
I'm looking into speeding up my workflow using remote development containers on ARM servers, but it seems some tools are missing, nrfutil the first, to run a fully...
Hi there,
I am currently trying to use device sleep modes with Matter. Nevertheless, once I add "CONFIG_PM_DEVICE_RUNTIME=y" to my prj.conf, the main-method is not longer...
When flashing with SDK v3.0.1 the following error occurs:
-- west flash: using runner nrfutil -- runners.nrfutil: mass erase requested -- runners.nrfutil: reset after flashing...
Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
I'm not sure if this is the right place for this question.
I'm using the Settings subsystem for the BLE name.
When BLE is initialized inside matter, settings_load is only...
Hi Nordic Team,
I’m currently doing POC using the nRF54L15.
As part of the initial testing phase, I’m evaluating the " nrf/adc driver sequence sample" from the nRF Connect...
Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
