Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi Nordic support,
I want to use the OOB key pairing and I found the below discussion:
Set OOB key on Master Control Panel?
This means I need to implement the application...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
I am trying develop a project in which when we request a characteristic from phone( read request), we will read data from other module through UART and give reply back. I...
Hi,
I designed before my board for 2 layer PCB and i used the coplanar waveguide with ground-plane in the bottom. now i want to move to the 4 PCB layer and i choose the...
Hi, I'm porting my project from SDK8.1 to SDK10.
I replace static app_timer_id_t m_beacon_timer_id; to APP_TIMER_DEF(m_beacon_timer_id);
to avoid hardfault when creat...
Hi all:
I modified DFU-BLE to make it suitable for S130 on nRF51822. I made the following modifications:
On "dfu-ctr1_pt_add"
ble_gatts_attr_md_t cccd_md;
memset...
Hello!
Until now I am using a nRF24L01 with johanson balun (2450BM14A0002) and MIFA.
I want to add a power amplifier to my nRF24L01 project. Can anyone give me advice which...
Hi
I have a programming issue with nRF51822. I am using the nrfjprog.dll to program this microcontroller in my test equipment via J-link Plus. When I have programmed a...
I am using single NRF24LU1P-F32Q32-T ic.i am using it only as a TAG transponder card .i wanted to know that can we program it to transmit only if there is no other controller...
hello everybody,
I measured the current consumption in two cases : in the advertising mode the current is around 4 ~ 5uA, & in the connected mode, the current is 160 uA...
Hi,
I am new to forum and to Ble. sorry about my week English.
I am working on a project where I am reading adc value every 1s and sending it over ble. So I have written...
Hi,
I'm using nRF dev kit with Softdevice 1.0.0.3.alpha. The device shows advertising state at LED1 as it should, however i can't detect "Nordic_UART" via nRF Master Control...
