Hello, I have an nrf52840 which is acting as a central. I have a peripheral device which I can connect to, and the service that is discovered has the following table:
ATT...
Hi, We are trying to get our nRF54L15 running, but are running into clock issues. The hardware is configured without an external 32kHz crystal, so we want to rely on the NRF54...
Hello!
I'm taking some performance metrics for encrypting data on my nRF52840 device and I was wondering if you might be able to help me. The goal is to see how long and...
Hi,
why antenna trace is connected to mounting pad instead of feeding pad of antenna in thingy 91x
We are designing our device based on this. We wish to be sure about...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
I have a custom board with nRF52840. It draws power over USB and the data lines are connected as well
USB is defined as follows in the dts
cdc_acm_uart0: cdc_acm_uart0...
Hello,
I am getting a 0xdeadbeef assertion at src\soc_radio_timeslot.c line 390. I am using S110 SoftDevice v7.1.0 with nRF51822 revision 2 CEAA. I am using the multiprotocol...
Hi,
i'm newbie to ANT world and i'm trying to create a mesh-like network using broadcast messages and shared channel with nRF51422 SoC and S310 soft-device.
So, i created...
Hi all,
I've been trying to develope a project by using an nRF51822 chip. The project is about to finish. However, I couldn't implement the pstorage module in a correct way...
I am looking to re-install the firmware on my dongle after making it a sniffer but I can't find a hex file for PCA10031. My MasterControlPanel has firmware for PCA10000 should...
Hi
Should I get a characteristic write event ( BLE_GATTS_EVT_WRITE ) with s110 as well with the
following property configuration:
char_md.char_props.write = 0;
char_md...
I try to achieve something similar to IBeacon where data is pushed to any device listening, but where the data is changing over time. Is it possible to (frequently) change...
Hello,
I have recently had to install the nrf tools on a mac computer. The tools have been recently ported to macs, but unfortunately I am getting the following message...
Greetings,
During a connection between two nrf51422s running on S120 (2.1.0) and S110 (8.0.0) with a connection interval of 7.5 ms I get only a maximum RSSI of -42 dBm...
Hello,
I developed a firmware on nrf51422 with nrf51. I use a development board PCA10028.
With this firmware I control the directly the radio registers (Soft Device is...
I have a nRF51822-EK evaluation kit (so, PCA10001) and am trying to get DFU working with an S120 SoftDevice as per the answer posted here:
devzone.nordicsemi.com/.../ ...
nRF51822
I'm interested in setting up the the POFCON to enable me to get a
POFWARN interrupt when the battery voltage drops below 2.7V.
The softdevice is enabled at...
I have a nRF51422 dongle, and I want to know the power/current when an UART event happens.
I've read nRF51822_Development_Kit_User_Guide_v1.4 p.29 for Current Measurements...
Hello,
I am experiencing some CC register issue in Timer of nRF51822. I am trying to setup TIMER1 for 16 seconds. But I see, that when I try to write to CC registers, the...
