I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
In my application I want to communicate nRF24L01+ with nRF51822 with dynamic length. Some settings are:
In nRF24L01+ side (reference: devzone.nordicsemi.com/.../)...
Hi,
Now I use these fun in ANT SD210 like below:
void MyFlashWrite(ble_ant_csc_t* cscdata)
{
uint32_t addr;
uint32_t patwr[3];
uint32_t pg_size;
uint32_t pg_num;...
what information does the nrfjprog.exe write to UICR(User Information Configuration Registers) register??
==========Tutorial of Flashing dfu bootloader to the nRF51 DK...
I want to use the ble sniffer to capture two peripherals connected to the master control panel.
with the ble sniffer I can only select one peripheral for capturing packets...
Hey there, I've posted this issue on the tutorial website and I came across a post stating that posting here will get me a quicker response. Here's my problem, when I tried...
In my application need to nrf8001 connect(bond) to e phone in a specific duration (for example 1 hours )and then disconnect and in one hour later bond again. In this duration...
Hi,
I am developing a Heart Rate application.
I need to ensure that i am flashing correct softdevice file through my application.
How can i do that?
Regards,
Sum...
Hi,all
i study DFU step by step according this link devzone.nordicsemi.com/.../a00076.html,but failed at step 8.my peripheral advertising as Nordic_HRM not dfuTag.
Can someone...
hi,
I used previously nrfjprog version 5 to program SD+APP+BL with --dfu flag and I can perform OTA DFU.
Now with version 7 there is no --dfu flag anymore and if I try...
Same question as devzone.nordicsemi.com/.../
What needs to change for a gcc setup in the compile flags.
If that helps, some of the flags I have now include:
-mfloat...
Hi,
I'm using s130 and my mcu is both central/peripheral. In the centrol role, when I try to connect and pair with an peripheral, I get all the way through SMP pairing...
I have been developing an application using PCA10028 board which needs to use timer. From the SDK8.0.0 pack, I found an example "timer_pca10028". It works fine when the SD...
Hi,
I'm trying to get a simple single packet transmit-receive working with the nRF51822. I have the following code shared between my transmitter and receiver:
#include...
Hello,
I am wondering how the Softdevice works internally with state changes because that's important for error handling. Here's an example:
Let's say the Softdevice...
